The Energon Pub

Here is my upgrade kit to turn the Transformers Prime Wheeljack mold into Transformers Prime Hot Rod!

*Update*

Version two of everything is ready to go.

For the head I used two base models with slight variations which gives me a total of 8 different versions. I think this is a good way to give everyone something that fits their needs. Both of the base models have been tested using FUD. The ball joint was a little loose do to production but it was easily fixed with some clear nail polish. With the test shot one of the horns broke off at some point, I doubled the thickness of the horns so they should be a stronger. I have also found out that during transformation it works best to rotate the head around and tilt it forward slightly, this will ensure that the head will not be in bind when in car mode. (I would like to thank Neekotron for his help with the design of the second head.)

The pipes and spoiler are now on ball joints to make them integrated with the transformation. The pipes and spoiler have been tested using WST and is the recommended material.

The pipes are held on using clips that slide on the lip at the bottom of the door/arm. The ball joint for the pipes can be a little loose but will hold in place without a problem. With them being on a ball joint it makes it so they can be angled to fill in some of the space between the pipes and door.

The spoiler sits a little high in car mode but gives good clearance in bot mode. It plugs into the location of the current, smaller stock spoiler. It is tight without the placement of screws but the mount has holes to allow the reuses the stock screws that are used with the stock spoiler.

Now that everything is reworked I will try my hand at painting, this should prove to be interesting.

Thanks for looking and please leave suggestions and comments.

Everything can be found in my Shapeways shop. http://www.shapeways.com/shops/benbots?l=36&galleryViewList=0

very cool man, looks great. The head doesn't say "hot rod" to me though. Looks more like an Iron Hide. I think it's the lack of head crest that's doing it.

The wings fit nicely though and I look forward to seeing further developments in this project.

That works pretty well, actually! Neato! Good eye seeing Hot Rod through all that garish Dead End coloring.

I would tend to agree that the expression could be a bit more Hot Rod-esque...and he'd probably be the only Prime cast member with a sniffer as he is. But that's just me. (I give you huge props for getting his head proportionate. My own attempt at a Hot Rod head in Sketchup yielded a far less healthy-looking cranium.)

Awesome!

Though in canon, Hotshot is actually Hotrod, so it would be strange owning 2. But still, pretty creative.

*Update*

Version two of everything is ready to go.

For the head I used two base models with slight variations which gives me a total of 8 different versions. I think this is a good way to give everyone something that fits their needs. Both of the base models have been tested using FUD. The ball joint was a little loose do to production but it was easily fixed with some clear nail polish. With the test shot one of the horns broke off at some point, I doubled the thickness of the horns so they should be a stronger. I have also found out that during transformation it works best to rotate the head around and tilt it forward slightly, this will ensure that the head will not be in bind when in car mode. (I would like to thank Neekotron for his help with the design of the second head.)

The pipes and spoiler are now on ball joints to make them integrated with the transformation. The pipes and spoiler have been tested using WST and is the recommended material.

The pipes are held on using clips that slide on the lip at the bottom of the door/arm. The ball joint for the pipes can be a little loose but will hold in place without a problem. With them being on a ball joint it makes it so they can be angled to fill in some of the space between the pipes and door.

The spoiler sits a little high in car mode but gives good clearance in bot mode. It plugs into the location of the current, smaller stock spoiler. It is tight without the placement of screws but the mount has holes to allow the reuses the stock screws that are used with the stock spoiler.

Now that everything is reworked I will try my hand at painting, this should prove to be interesting.

Thanks for looking and please leave suggestions and comments.

Everything can be found in my Shapeways shop. http://www.shapeways.com/shops/benbots?l=36&galleryViewList=0

looks great man, I'm looking forward to seeing it all painted up