The Energon Pub

by **TENIME_art** » Fri May 25, 2007 5:14 pm

The only purpose for the (yes, air-drying) "Paperclay" was to provide a flat surface for the G1 Reprolabel sticker to rest. If it was going to be exposed, then, of course I would've taken more time and care to make it better (I'm a perfectionist!)... But, since the sticker will be covering it, I just needed something for the sticker to rest on. Not to mention, this is the first time I've ever used clay (other than the obligatory "4th grade, making an ashtray" type of sculpting).

Don't worry. I think I kind of, pretty much, hope I know what I'm doing.

Also, don't you have to cook Milliput? I'm not putting action figure parts in the oven, when they're getting harder and harder to find, and me, without money or a way to acquire it...

by **jimsloth** » Fri May 25, 2007 5:25 pm

not the stuff I use, you just mix it together (two parts) and it cures like epoxy.

by **TENIME_art** » Fri May 25, 2007 7:20 pm

Thank you. Like I said, Jazz is my cherry-popping kitbash...

by **tentagil** » Fri May 25, 2007 8:32 pm

Yeah Milliput is a two part epoxy clay. You mix the two clays and they react to each other and cure over time. great for custom stuff. I personally like Green Stuff better, but its a little harder to find and more expensive.

by **TM TM2 Dinobot** » Fri May 25, 2007 10:34 pm

TENIME_art wrote:Thank you. Like I said, Jazz is my cherry-popping kitbash...

HORRIBLE mental image!!! >.<

by **TENIME_art** » Tue May 29, 2007 5:37 pm

TM2 Dinobot wrote:
TENIME_art wrote:Thank you. Like I said, Jazz is my cherry-popping kitbash...

HORRIBLE mental image!!! >.<

Since I don't want to start putting him together until it's been two weeks (even though Fusion only says 7 days), I thought I'd make some little teaser photos.

Glued the headlights in:

(didn't need to worry about paint scratching for that)

And, since it's been over two weeks since i did the black parts, here's more of the skeleton:

Enjoy!!

by **jimsloth** » Tue May 29, 2007 6:18 pm

That is lookin' sweet. I don't have anywhere near the patience you have. With fusion my stuff is usually put back together within a couple hours of spraying.

by **TM Mega-Prime** » Sun Jun 03, 2007 5:55 pm

Hey this looks great so far!! The Krylon Fusion paints you are using, do you prime the parts before you spray them with the fusion paint?

by **tentagil** » Sun Jun 03, 2007 6:01 pm

Mega-Prime wrote:Hey this looks great so far!! The Krylon Fusion paints you are using, do you prime the parts before you spray them with the fusion paint?

Krylon is made to be put on plastic without primer. It bonds with the top layer of the plastic to make it more scratch resistant.

by **TENIME_art** » Tue Jun 05, 2007 12:11 am

tentagil wrote:
Mega-Prime wrote:Hey this looks great so far!! The Krylon Fusion paints you are using, do you prime the parts before you spray them with the fusion paint?

Krylon is made to be put on plastic without primer. It bonds with the top layer of the plastic to make it more scratch resistant.

Yes.

Thank you!

by **TENIME_art** » Wed Jun 06, 2007 6:12 pm

Still waiting for the overcoat on the taillights to dry. I don't want to hammer that super-long pin back in, and risk screwing up any of the stickers...

by **jimsloth** » Wed Jun 06, 2007 6:23 pm

did something happen to the windshield or is that just a funky pic?

by **TENIME_art** » Wed Jun 06, 2007 9:15 pm

Both.

I got white paint on it, and successfully removed it. In person, it looks fine, but the camera flash seems to make it all spotty and blurry.

When it's all done, I'll be using my best friend's camera and some lighting. It won't look like this, trust me.

by **tentagil** » Wed Jun 06, 2007 9:22 pm

Loving it. Though I think I'm gonna get the Movie Final Battle Jazz and bash some hands and a new head on it for my own classics Jazz. Partially because I can't find any more BBs around here.

by **Nemesis Sturmvogel** » Thu Jun 07, 2007 12:24 am

It looks good.

The Energon Pub

Classics Jazz WIP

Who is online

Forums

Transformers News

Transformers and More @ The Seibertron Store

Featured Products on Amazon.com

The Ultimate Caption Contest