The Energon Pub

News Credits: 4838 · by **william-james88** » Thu Jan 11, 2018 10:36 am

Optimus Eeyore wrote:Found men at Walmart tonight

I guess Walmart is better than a singles bar then.

News Credits: 11 · by **Lore Keeper** » Thu Jan 11, 2018 10:56 am

william-james88 wrote:
Optimus Eeyore wrote:Found men at Walmart tonight

I guess Walmart is better than a singles bar then.

What state was that Walmart in?

News Credits: 65 · by **Wolfman Jake** » Thu Jan 11, 2018 11:43 am

william-james88 wrote:
Optimus Eeyore wrote:Found men at Walmart tonight

I guess Walmart is better than a singles bar then.

Walmart: Always low standards!

News Credits: 11 · by **Lore Keeper** » Thu Jan 11, 2018 12:01 pm

So, update. I finally found another Rodimus (#4). He is from the same batch code as my last one, so expectations weren't high. His exhaust pipes were similarly tight to my other copies. However, both arms did manage to fully rotate back and forth on the plastic stops with no apparent damage or breakage. They remain fairly tight, even after a good amount of manipulation. I still have some lingering concern that they'll eventually break from repeated stress, but so far it appears I may have finally found a Roddy that will join my collection!

News Credits: 65 · by **Wolfman Jake** » Thu Jan 11, 2018 12:12 pm

Lore Keeper wrote:So, update. I finally found another Rodimus (#4). He is from the same batch code as my last one, so expectations weren't high. His exhaust pipes were similarly tight to my other copies. However, both arms did manage to fully rotate back and forth on the plastic stops with no apparent damage or breakage. They remain fairly tight, even after a good amount of manipulation. I still gave some lingering concern that they'll eventually break from repeated stress, but so far it appears I may have finally found a Roddy that will join my collection!

Best of luck!

News Credits: 241 · by **Jelze Bunnycat** » Thu Jan 11, 2018 4:19 pm

Wolfman Jake wrote:
Lore Keeper wrote:So, update. I finally found another Rodimus (#4). He is from the same batch code as my last one, so expectations weren't high. His exhaust pipes were similarly tight to my other copies. However, both arms did manage to fully rotate back and forth on the plastic stops with no apparent damage or breakage. They remain fairly tight, even after a good amount of manipulation. I still gave some lingering concern that they'll eventually break from repeated stress, but so far it appears I may have finally found a Roddy that will join my collection!

Best of luck!

Keep us informed! ;)^

News Credits: 11 · by **Lore Keeper** » Fri Jan 12, 2018 2:06 pm

Still no breakage. I managed to get a full video review recorded which will be uploaded and posted tonight.

News Credits: 65 · by **Wolfman Jake** » Fri Jan 12, 2018 3:26 pm

Lore Keeper wrote:Still no breakage. I managed to get a full video review recorded which will be uploaded and posted tonight.

Yay!

by **cr3d1t** » Sat Feb 03, 2018 6:12 pm

Picked up PotP RP yesterday from my local shop. It has a batch number of 73111, which is earlier than the others I saw posted. I have no problems with the arms.

News Credits: 11 · by **Lore Keeper** » Sat Feb 03, 2018 6:24 pm

cr3d1t wrote:Picked up PotP RP yesterday from my local shop. It has a batch number of 73111, which is earlier than the others I saw posted. I have no problems with the arms.

Good to hear. I haven't heard any new reports of breakage, so I'm inclined to think it was a very limited issue.